Also on the truck · Eden Prairie & the west metro
The rest of the lineup
Same $99 diagnostic, same written price, same written warranty on every machine we fix in Eden Prairie & the west metro.
The oven that stalls at 300 with a roast inside, a gas burner that clicks and never catches, a glass-top with one dead zone, an F-code the night before Thanksgiving.
Mon–Fri 8am–6pm · Sat 9am–3pm · Eden Prairie-based, no mileage charge inside 30 minutes
Same $99 diagnostic, same written price, same written warranty on every machine we fix in Eden Prairie & the west metro.
The Sunday before Thanksgiving is the busiest day of our year, and the second busiest is the week the state fair ends and everyone starts baking again. Between those two dates we work on every kind of cooking appliance the west metro owns. Freestanding gas ranges in the 1970s and 1980s houses of Eden Prairie’s Preserve and Bloomington’s west side, thirty-inch electric slide-ins in the 2000s kitchens off Anderson Lakes Pkwy and in Chanhassen, double wall ovens with a separate cooktop in the remodeled kitchens of Edina and the Minnetonka lake homes, and induction tops in the newest builds. The shop sits a block off Prairie Center Dr, so most of it is a short run.
Cooking appliances fail from heat and time more than from water, which makes them the one machine our hard water leaves alone. What we see instead is the bake igniter on a gas oven that glows but never gets hot enough to open the valve, the bake element on an electric oven that splits and sparks mid-roast, the surface element switch that welds itself on or off, and the control board that throws an F-code every time the humid July air gets into the keypad. Wolf, Thermador and Viking ranges in the Bearpath and Indian Hills kitchens fail in the same places, just with heavier parts.
The bake igniter is weak. It still glows, but it no longer draws enough current to open the safety valve fully, so the burner lights late or cycles off. We measure the igniter’s amperage with the meter and replace it from the truck; it is the most common oven repair we do.
The bake or broil element has burned through, or a relay on the control board no longer sends it power. A broken element often shows a bright spot or a visible split. We test the element’s resistance and the board relay, replace what has failed, and check temperature with a probe.
On gas cooktops, a wet or cracked spark igniter, a corroded electrode, a burner cap sitting crooked or a spark module that has quit. On sealed burners, scale and boil-over residue block the ports. We clean and align first, then test the module and replace the electrode if it is the cause.
A failed radiant element, a surface element switch, or on induction a coil or the generator board. Sometimes a pan sensor is reading wrong. We test the element circuit and the switch with the meter, and on induction read the board’s error history before naming the part.
F1, F2, F3 and their cousins point to the oven temperature sensor, the door lock on self-clean models, a stuck keypad or the control board itself. We look up the code for your exact model, test the sensor’s resistance at room temperature, and only condemn the board when the sensor and wiring pass.
The lock motor or latch switch has failed in the locked position, or the door hinges have lost their spring tension. We release the latch without damaging the trim, test the lock assembly, and replace hinges as a pair so the door seals evenly and heat stops leaking into the kitchen.
A cooking appliance is easier to read than most, because its parts either heat or they do not. The technician confirms the complaint with a temperature probe, then goes straight to the meter: amperage on a gas igniter, ohms across an electric element, resistance on the oven sensor at room temperature, voltage at the switch or board relay. Gas connections get checked for leaks before and after. The failed part is named in plain words, and one price goes on paper. Approve it and the part usually comes off the truck and the oven is back to temperature before we leave. Decline it and the $99 is the entire charge.
Whirlpool, GE, Frigidaire, Samsung, LG, KitchenAid, Maytag, Kenmore and Bosch are most of what we open, plus the Wolf, Thermador, Viking, Dacor and JennAir ranges and wall ovens in the built-in kitchens of Edina, Wayzata and the Lake Minnetonka shoreline. Landlords with rentals around Eden Prairie Center or Uptown can have the tenant host while the owner approves by text and receives the invoice and written warranty by email. A board or a brand-specific element that must be ordered comes back with no second trip fee, and we try to leave the cooktop usable in the meantime. All oven and range pricing is set after the diagnostic and put in writing, with the $99 folded into the number you approve.
We try hard, and the earlier in the week you call, the better the odds. Most oven faults are igniters, elements and sensors that ride on the truck, so a visit in Eden Prairie, Minnetonka or Chanhassen early in the week usually means a working oven by the holiday. A board that has to be ordered is the exception, and we will say so at the door.
No. A healthy gas oven reaches 350°F in about twelve to fifteen minutes. A slow preheat almost always means a weak bake igniter that is opening the gas valve late in each cycle. It will eventually fail entirely, often mid-roast. The repair is quick and the part is on the truck.
Yes. Double wall ovens and separate gas or induction cooktops are standard in the remodeled kitchens of Country Club, Indian Hills, Rolling Green and the lake homes off Hwy 7. We pull the oven from the cabinet with a lift when needed, protect the cabinetry, and reinstall it level and sealed.
If the burner lights and the clicking stops, yes, though it usually means the igniter is wet or cracked and will get worse. If a burner is releasing gas without lighting, turn it off and stop using it until we have looked at it. We test the spark module and check the gas connections on every gas call.
Not yet. Most F-codes point to the oven temperature sensor, the door lock or the keypad, and the board is the last suspect, not the first. We look up the code for your model, test the sensor and wiring with the meter, and replace the board only when everything upstream of it passes. That order saves a lot of Eden Prairie homeowners an unnecessary part.
Call (763) 342-9995 or send the form. You get a callback with a real arrival window, and a text when the truck is on its way.
The technician tests the machine, names the failed part in plain words, and writes one flat price. The $99 is already inside it.
We stock the parts that actually fail in west-metro homes, so most jobs close the same visit; an ordered part comes back with no second trip fee.
Full test cycle before we pack up, a clean work area after, and a written warranty on the invoice.
One call starts it: $99 finds the fault, one written number, repair from the truck, written warranty.
