A GE range in a Hennepin Village kitchen flashing F3 before a dinner, a GE dishwasher near Anderson Lakes holding water with C1, a GE top-loader that hums but will not spin.
Mon–Fri 8am–6pm · Sat 9am–3pm · Eden Prairie-based, no mileage charge inside 30 minutes
Refrigerator & Freezer Repair$99 finds the fault · price on paper
Washer Repair$99 finds the fault · price on paper
Dryer Repair$99 finds the fault · price on paper
Dishwasher Repair$99 finds the fault · price on paper
Oven, Range & Cooktop Repair$99 finds the fault · price on paperIce Maker Repair$99 finds the fault · price on paper
The builders who filled Eden Prairie from the 1990s through the 2010s, in Hennepin Village, later Bearpath and the townhome rows around Anderson Lakes, put a GE range and dishwasher in nearly every kitchen and a GE top-load pair in the laundry off the garage. Owners who remodeled upgraded to GE Profile and Café, and the rental townhomes replaced worn sets with the same GE models by the dozen. The result is a city where GE is the range under most hoods, and where the F2, F3 and F7 codes on a GE display are the most common oven call we take.
Eden Prairie’s water is pumped from municipal wells and arrives hard, with iron in the streets toward the Minnesota River, and a GE machine here relies on the softener in the utility room to keep it clear. When the softener runs out of salt, the GE dishwasher heater scales white and the C1 drain code follows as grit and lime slow the pump. The GE washer inlet valve narrows until fills drag, and the GE refrigerator’s ice maker fills short. Winter closes the list: a GE dryer venting through a second-floor wall near Staring Lake runs cold when the cap ices, and a GE refrigerator in a three-stall garage off Dell Rd stops running when the slab drops toward freezing.
| Machine | Common symptom | What it usually is | What we do |
|---|---|---|---|
| Washer | GE top-loader fills, agitates, then stops with the lid locked before spin | Lid lock or lid switch reading open, or the drive motor and inverter losing the position signal | Test the lock and switch, read the motor windings and inverter output, replace the failed part, prove a full spin |
| Dryer | Second-floor GE dryer takes two cycles in January, then no heat | Vent cap iced shut, thermal fuse opened by trapped heat, or an element reading open | Check airflow at the machine, ohm the fuse and element, replace what opened, tell you if the vent needs cleaning |
| Refrigerator | Sheet of ice under the bottom-freezer drawer, water on the kitchen floor | Defrost drain frozen, often with a failed drain heater or clogged drain tube | Thaw and clear the drain, replace the heater or tube, run the defrost cycle so the ice does not return |
| Range / oven | F2, F3 or F7 on a GE or Profile range, oven shuts itself off | Oven sensor out of range, a relay that ran too hot, or a shorted key on the touch pad | Read the sensor, test the relay board and keypad, replace the failed part, confirm the oven cycles at set temperature |
| Dishwasher | C1 code, water in the sump, film on glasses in a house whose softener ran out of salt | Drain pump slowed by scale and grit, check valve stuck, heater coated by hard water | Clear the sump and check valve, test the pump, descale and test the heater, run a wash and drain to confirm |
| Ice maker | Ice slows, cubes small, fill tube frozen in a garage refrigerator | Fill valve narrowed by scale, or a frozen fill tube in an unheated garage | Measure fill volume, replace the valve, thaw and insulate the tube, test the ice maker through a full harvest |
| Code | What it means | What we do |
|---|---|---|
| F2 | Oven over-temperature — the control saw the cavity run too hot | Meter the oven sensor, test the bake relay, check the self-clean lock, replace the part that failed |
| F3 / F4 | Oven sensor shorted (F3) or open (F4) as read by the control | Read the sensor at its plug, check the harness behind the oven wall, replace the sensor, bake-test |
| F7 | Stuck or shorted key on the range touch pad | Unplug the keypad, test each key line, dry a spill or replace the panel, confirm the control answers |
| F9 | Door latch did not reach its locked or unlocked position | Test the latch motor and switches, clear the latch path, replace the lock assembly if it fails |
| C1 / C2 | Dishwasher pump-out ran too long to empty the sump | Clear the sump, filter and check valve, test the drain pump under load, replace a weak pump |
| E22 / E23 | Washer fill (E22) or drain (E23) took longer than the control allows | Check the supply and drain paths, meter the inlet valve or drain pump, replace the part that fails |
An Eden Prairie GE call is a short trip from Commonwealth Dr, and the diagnosis starts with the code you photographed and a test of what it points at. For an F3 we ohm the oven sensor at its plug and at the board, because a chafed harness gives the same code as a failed sensor. For a dishwasher C1 we time the drain and pull the check valve before deciding the pump is done. GE oven sensors, bake and broil elements, igniters, dishwasher drain pumps and check valves, washer lid locks, dryer fuses and belts, and refrigerator drain heaters ride on the truck, so most Eden Prairie GE repairs close the same visit. An ordered part comes back with no second trip fee.
Because so many Eden Prairie GE machines came with a new or newly remodeled house, we ask the age before quoting. A range or dishwasher still within the maker’s coverage should be fixed under it, and we say so instead of charging you. A store plan gets the same honest answer. Owners of rental townhomes around Eden Prairie Center approve by text while the tenant hosts, and the invoice and written warranty arrive by email. The pricing rule is the same on every street in the city: the $99 diagnostic is folded into the repair price you approve, so a yes does not add it back. Decline and $99 is the full bill. Every price follows the diagnostic, in writing, and every repair carries a written warranty.
Yes. The townhomes around Eden Prairie Center and Anderson Lakes were built with GE ranges, and F2, F3 and F7 codes are the most common oven calls we take from them. For a rental, the tenant lets us in, the owner approves the written price by text, and the invoice and written warranty are emailed. Oven sensors, elements, igniters and keypads for common GE models are on the truck.
C1 means the dishwasher took too long to pump out and the control stopped the cycle. Eden Prairie’s hard well water leaves scale and grit in the drain pump and check valve, especially once the softener runs low on salt, and the pump slows until the code appears. Check the filter first. If C1 returns, we clear the sump, test the pump under load and replace it if it has lost strength.
Usually, yes. F3 means the control reads the oven temperature sensor as shorted, and most of the time the sensor has failed. Occasionally the harness behind the oven wall has chafed and gives the same code, so we test the sensor at its plug and again at the board before replacing anything. The sensor for common GE and Profile ranges is on the truck, and the oven is bake-tested before we leave.
It shortens the life of the inlet valve, yes. Eden Prairie’s well water is hard, and the screens and seats inside a GE washer inlet valve scale down until fills drag and the machine may report E22. A softener that is kept in salt slows this considerably. We time the fill, meter the valve coils and replace the valve, then show you the water at the hose so the softener gets attention.
When the refrigerator is warm, yes. Eden Prairie is the shop’s home city, and a GE bottom-freezer or side-by-side that stopped cooling in Hennepin Village or Hidden Ponds usually gets a window that day. Defrost heaters, drain heaters, evaporator fans and thermistors are on the truck. Other GE repairs in Eden Prairie are scheduled the same week, often the next day.
Call (763) 342-9995 or send the form. You get a callback with a real arrival window, and a text when the truck is on its way.
The technician tests the machine, names the failed part in plain words, and writes one flat price. The $99 is already inside it.
We stock the parts that actually fail in west-metro homes, so most jobs close the same visit; an ordered part comes back with no second trip fee.
Full test cycle before we pack up, a clean work area after, and a written warranty on the invoice.
One call starts it: $99 finds the fault, one written number, repair from the truck, written warranty.