Also on the truck · Minnetonka
The rest of the lineup
Same $99 diagnostic, same written price, same written warranty on every machine we fix in Minnetonka.
A Minnetonka wall oven that will not pass 275, a pro-style range with a burner that clicks and never lights, an induction top that stopped seeing the pan.
Mon–Fri 8am–6pm · Sat 9am–3pm · Eden Prairie-based, no mileage charge inside 30 minutes
Same $99 diagnostic, same written price, same written warranty on every machine we fix in Minnetonka.
A 1960s house in Minnetonka has usually had its kitchen redone at least once, and the cooking appliances tell you when. The first remodel, in the 1990s, put in a thirty-inch slide-in and maybe a wall oven with a separate cooktop; the second, in the 2010s, brought a Wolf or Thermador range or a pair of Viking wall ovens and an induction top into the homes toward Lake Minnetonka and the bigger lots around Glen Lake. Around Ridgedale and along Hwy 7 the 1980s and 1990s houses still have the original freestanding electric range or its first replacement. We come up Hwy 101 or I-494 from the shop in Eden Prairie with parts for all three generations.
Cooking appliances are the one machine in a Minnetonka house that the hard water leaves alone, so what fails is what heat and time wear out. On gas: a bake igniter that glows orange but no longer pulls enough current to open the safety valve, so the oven lights late and cycles off early. On electric: a bake element that splits and arcs mid-roast, or a surface element switch that welds itself on. On the pro-style ranges: spark modules, oven sensors and the heavy door hinges that let heat leak into the kitchen. Control boards throw F-codes when the humid July air finds the keypad.
The bake igniter has weakened. It still glows but does not draw enough current to hold the gas valve open, so the burner lights late and quits early. We read the igniter’s amperage with the meter and replace it from the truck. On Wolf and Thermador ranges the igniter is a heavier part but the fault is the same.
The bake or broil element has burned through, or a control board relay has stopped sending it power. A visible split or bright spot on the element usually confirms it. We test resistance across the element and the relay output, replace what failed, and check the oven with a probe.
A cracked or wet spark igniter, a corroded electrode, a burner cap off center, or a spark module that has quit. On sealed burners, boil-over residue in the ports does it. We clean and realign first, then test the module and replace the electrode when it is the cause.
On radiant tops, a failed element or the surface element switch behind the knob. On induction, a coil, the generator board or a pan sensor reading wrong. We test the element circuit and switch, and on induction read the board’s error log before naming a part.
Most codes point to the oven temperature sensor, the door lock on self-clean models or a stuck keypad, with the control board last on the list. We look up the code for your exact model, test the sensor’s resistance at room temperature, check the wiring, and only then condemn the board.
The door lock motor has failed in the locked position after a self-clean cycle, or the hinges have lost their spring tension. We release the latch without damaging the trim, test the lock assembly, and replace hinges as a pair so the door seals evenly and the kitchen stops heating up.
The technician confirms the complaint with a temperature probe, then goes to the meter: amperage on a gas igniter, ohms across an element, resistance on the oven sensor at room temperature, voltage at the surface switch or board relay. On gas ranges the connection behind the unit is checked for leaks before and after. Wall ovens come out of the cabinet with a lift when they must, and the cabinetry gets protected. The failed part is named in plain words and one price is written. Approve it and the part usually comes off the truck and the oven is back to temperature before we pack up. Decline it and $99 is the entire charge.
Whirlpool, GE, Frigidaire, Samsung, LG, KitchenAid, Maytag and Bosch are most of what we open in Minnetonka, plus the Wolf, Thermador, Viking, Dacor and JennAir ranges and wall ovens in the homes toward Lake Minnetonka and around Glen Lake. Landlords with rentals near Ridgedale or along Hwy 7 can have the tenant host while the owner approves by text and receives the invoice and written warranty by email. A board or brand-specific element that has to be ordered comes back with no second trip fee, and we try to leave the cooktop usable meanwhile. Every Minnetonka oven and range repair is priced after the diagnostic, in writing, with the $99 already inside.
Yes. Pro-style ranges and wall ovens in the Lake Minnetonka homes and the Glen Lake remodels are a regular part of the route. They fail in the same places as any other range, at igniters, spark modules, oven sensors and door hinges, only with heavier parts. We carry the common ones and price the repair in writing before starting.
The earlier in the week you call, the better. Most oven faults are igniters, elements and sensors that ride on the truck, so one visit to a Minnetonka address usually means a working oven by the holiday. If the fault is a control board that must be ordered, we say so at the door and the cooktop is usually still usable.
Almost certainly. A healthy gas oven preheats to 350°F in twelve to fifteen minutes. A weak bake igniter opens the gas valve late in each cycle, stretching the preheat and eventually failing outright, usually mid-roast. We measure its current with the meter to confirm, and the part is on the truck.
If it lights and stops clicking, yes, though the igniter is likely wet or cracked and will get worse. If gas is flowing without a flame, turn the burner off and stop using it until we have looked. We test the spark module and check the gas connection for leaks on every gas range call.
Not yet. Most F-codes point to the oven temperature sensor, the door lock or the keypad, all of which are cheaper and more likely than the board. We look up the code for your exact model, test the sensor and its wiring, and only recommend a board when everything upstream passes. The written price comes before you decide.
Call (763) 342-9995 or send the form. You get a callback with a real arrival window, and a text when the truck is on its way.
The technician tests the machine, names the failed part in plain words, and writes one flat price. The $99 is already inside it.
We stock the parts that actually fail in west-metro homes, so most jobs close the same visit; an ordered part comes back with no second trip fee.
Full test cycle before we pack up, a clean work area after, and a written warranty on the invoice.
One call starts it: $99 finds the fault, one written number, repair from the truck, written warranty.
